Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
3dprinters [2016/05/29 12:43]
John Benedetto [Training & Problems]
3dprinters [2019/02/14 05:02] (current)
John Benedetto [Makes and models]
Line 7: Line 7:
 ===== Makes and models ===== ===== Makes and models =====
  
-    ​* [[hardware:​3dprinter:​prusa_mendel|Prusa Mendel]] +  ​* [[:​prusa_mendel|Prusa Mendel]] 
-    * [[:​hardware:​3dprinter:​prusai3|Prusa ​i3]] +  * [[:​prusai3|Prusa ]] 
-    * [[:hardware:​3dprinter:​orion|SeeMeCNC ORION Delta Printer]] +  * [[:blinky|]] - troybot 
-    * [[:printirnator|Printirnator]] +  * [[:orion|SeeMeCNC ORION Delta Printer]] 
-    * [[:​makerbot|Makerbot Cupcake / Thing-o-Matic]]+  * [[:​makerbot|Makerbot Cupcake / Thing-o-Matic ​- Thing1 & Thing2]]
  
 ===== Training & Problems ===== ===== Training & Problems =====
  
-To get trained ​to use Quelab'​s ​3D Printerssign up for the [[http://​pepper.quelab.net/​mailman/​listinfo/​3d-printing|3d-printing mailing list]], then send a request, asking for training. ​ There is often a traning-qualified member attending HackNight((Hacknight is Quelab’s version of an active open house. We encourage our members ​to show up to work on projects, be social, and at the same time invite interested persons of the community to come on down and check it outThis also allows non-members to try out the space and to start makingas well as meet current members. Hacknights are also a great time to take a tour, get policy orientation,​ as well as some group training.)),​ but without prior agreement ​there is no guarantee ​someone ​will be there.+<WRAP important round> Training is currently in flux. To be trained ​on the 3D printersplease contact the 3D printing officer via the [[http://​pepper.quelab.net/​mailman/​listinfo/​3d-printing|3d-printing mailing list]] to set up meeting ​on an open nightWithout prior arrangement, there is no guarantee ​that there will be a 3D printing trainer available during an open night, however</​WRAP>​
  
-For information on troubleshootingplease refer to the [[:​hardware:​3dprinter:​troubleshooting|print troubleshooting]] ​page for how to figure out what's going wrong.+For information on usagetips and 3D printing stuff, see: 
 + 
 +  * Using [[:​3dprinter_usage|MatterControl]] ​to print models, as well as 
 +  * A set of [[:​hardware:​3dprinter:​care_and_feeding|troubleshooting ​and maintenance]] steps.
  
 ===== Materials ===== ===== Materials =====
  
-Different 3D printers accept different materials. Check the page for [[hardware:3dprinter#​makes_and_models|whichever printer you are using]] to identify allowable filament.+Different 3D printers accept different materials. Check the page for [[:3dprinters#​makes_and_models|whichever printer you are using]] to identify allowable filament.
  
 The table below specifies costs of materials kept at Quelab. The table below specifies costs of materials kept at Quelab.
  
-<WRAP info> All values are in //​per-gram// ​ increments of ALL consumed materials, **including** failed prints and support material.</​WRAP>​+<WRAP info> All values are in //​per-gram// ​ increments of ALL consumed materials, **including** ​ failed prints and support material.</​WRAP>​
  
-^Material ^Members ^Non-Members | +^Material^Members^Non-Members| 
-|ABS |$0.10 |$0.20 | +|ABS|$0.10|$0.20| 
-|PLA |$0.10 |$0.20 | +|PLA|$0.10|$0.20| 
-|NinjaFlex(([[hardware:​3dprinter:​prusai3|Prusa i3]] only)) ​ |TBD: Likely in the $0.60/g range || +|NinjaFlex(([[:​prusai3|Prusa i3]] only)) ​   |TBD: Likely in the $0.60/g range|| 
-|IGUS [[http://​www.igus.com/​wpck/​15422/​iglidur_TriboFilament|Tribo]] |Go get a sample from IGUS. It's expensive. ||+|IGUS [[http://​www.igus.com/​wpck/​15422/​iglidur_TriboFilament|Tribo]]|Go get a sample from IGUS. It's expensive.||
  
 Materials must be cleared by a 3D printing officer. Materials must be cleared by a 3D printing officer.
Line 41: Line 44:
   * NinjaFlex   * NinjaFlex
   * IGUS Tribo filament   * IGUS Tribo filament
 +  * Push Plastic ABS and PLA
 +  * Taulman Nylon 230
  
 Any material that is in the 3D printing room is considered cleared if it is on the rack above the 3D printers. Any material that is in the 3D printing room is considered cleared if it is on the rack above the 3D printers.
  
 +\\