Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
zoot_woodbook2014_tech [2014/12/16 21:55]
Craig Goldsmith created
zoot_woodbook2014_tech [2015/02/02 05:20] (current)
Line 3: Line 3:
 {{:​pc140185.jpg?​640x480}} {{:​pc140185.jpg?​640x480}}
  
-Troy gave me the idea for the hinges. These were done 2mm apart, as a single cut line on the cutter, i.e., the width of the slots is the width of the kerf of the cutter. Originally, I had designed a hinge where the slots were actually ovals, about 1.75mm wide. This gave me precise control over the width of the slot -- but doubled cutting time on. Between the slots and the engraving, wanted to get time per piece down to less than 45 minutes. I also tended to get embering and flareups on the hinges w/more material removed. Certainly setting cut order element by element would prevent that, by allowing the wood to cool down before a neighboring slot is cut.+Troy gave me the idea for the hinges. These were done 2mm apart, as a single cut line on the cutter, i.e., the width of the slots is the width of the kerf of the cutter. Originally, I had designed a hinge where the slots were actually ovals, about 1.75mm wide. This gave me precise control over the width of the slot – but doubled cutting time. Between the slots and the engraving, ​we wanted to get the time per piece down to less than 40 minutes. I also tended to get embering and flareups on the hinges w/more material removed. Certainly setting cut order element by element would prevent that, by allowing the wood to cool down before a neighboring slot is cut.
  
-In any case, the kerf at the bottom side of the cut is narrower, so I brought the speed way down to cut the slots cleanly on both sides in pass. Details about power settings are at bottom of this post.+The kerf at the bottom side of the cut is narrower, so I brought the speed way down to cut the slots cleanly on both sides in one pass. Details about power settings are at the bottom of this post.
  
-The wood material is the 24" x 24" luanne brand plywood ​at Lowe'​s ​that sells for $2.98. The hardware is 4-40 x 5/8 machine screws and nuts.+The wood material is the 24" x 24" luanne brand plywood ​we all know and love that Lowe's sells for $2.98. The hardware is 4-40 x 5/8 machine screws and nuts.
  
-These were engraved double sided by locking the raw material into the cutter and engraving and cutting the fronts sides completely. The pieces were then flipped within their cut outlines and the back sides engraved. This gives you relative registration within the kerf of the cutter, so say, 1-2mm. This presumes ​you can "​register"​ your second file (for the backs) with the front pass.+These were engraved double-sided by locking the raw material into the cutter and engraving and cutting the fronts sides completely. The pieces were then flipped within their cut outlines and the back sides engraved. This gives you relative registration within the kerf of the cutter, so say, 1-2mm, and presuming ​you can "​register"​ your second file (for the backs) with the fronts.
  
-This is made much easier by manually ​creating ​a tiny element in art at the far lower left that is completely ​off the "​box"​ that might otherwise enclose all the elements of your art. All vector software (like Adobe Illustrator,​ CorelDraw, LaserCut) relies on enclosing everything within a "​box"​ and then grabbing the lower left corner as the master reference point. This the blue dot/circle that shows the "​home"​ location in LaserCut. By manually placing an element at the lower left of your art that is not part of the final piece, you force that home origin point to be in the same place every time.+This is made much easier by manually ​placing ​a tiny element in the art at far lower left. This element should be completely ​outside ​the "​box"​ that might otherwise enclose all the elements of your art.
  
-For this projectthe front and back version of the file both have that same reference ​elementIt's the left-most, lower-most element so by definitionLaserCut will "​home"​ on it. It'​s ​actually a 1mm circle, and I set that as the first cut layer, so I can actually see prior the start of cutting if the piece is "​homed"​.+All vector software (like Adobe IllustratorCorelDraw, LaserCut) rely on enclosing everything within a "​box" ​and then grabbing the lower left corner as the master ​reference ​pointTechnically, it'​s ​called ​the bounding box (i.e. the "​bounds" ​of the total artwork), and the lower left is always the origin point, just like in Cartesian geometry.
  
-Cutting was done in layers, in this order. The reason for cutting the slots and engraving last is those take the longest, and this way I could see if the rest was OK before committing to possibly trashing the material. The art and text would have looked better had I gone to a higher scanline, but again, that would have driven the cutting/engraving time through the roof.+This origin point of the bounding box is the blue dot/circle that shows the "​home"​ location in LaserCut. By manually placing an element at the lower left of your art that is not part of the final piece, you force that home origin point to be in the same place every time. 
 + 
 +For this project, the front and back version of the file both have that same reference element. It's the left-most, lower-most element. By definition, LaserCut will "​home"​ on it. It's actually a 1mm circle, and I set that as the first cut layer, so I can actually see prior the start of cutting if the piece is "​homed"​. 
 + 
 +The art was created in Adobe Illustrator,​ organized as layers for cutting/​engraving. The native art file was exported as Illustrator 7 (which can be imported directly by LaserCut) with images embedded and all typefaces converted to outlines. 
 + 
 +Images were prepped in Adobe PhotoShop. Generally, I convert source material to grayscale, where I'll perform aggressive color corrections to bring out the details that might suitable for engraving. This grayscale version is then converted to bitmap, usually in the 600-1200dpi range. Depending on the nature of the image I may allow a dither or mezzotint into the bitmap conversion to simulate "​tone"​. However, I've only seen that kind of detail show up if engraving in material that shows detail very well (fine grain hardwood or acrylic) and if you really commit to the time it takes to engrave at scanlines upward of 600dpi. 
 + 
 +Cutting was done in six layers, in this order. The reason for cutting the slots and engraving last is those take the longest, and this way I could see if the rest was OK before committing to possibly trashing the material. The art and text would have looked better had I gone to a higher scanline, but again, that would have driven the engraving time through the roof.
  
 Settings are shown in speed/​power:​ Settings are shown in speed/​power:​
Line 25: Line 33:
     * art and text - engrave - s340/p40 - scanline 300dpi     * art and text - engrave - s340/p40 - scanline 300dpi
     * hinge slots - cut - s7/p100     * hinge slots - cut - s7/p100
 +    * final piece outline - cut - 10.1/100
 +
 +The three images below show the exported front/back files and the "​working"​ master art. The reference point is the tiny 1mm circle at lower left of both pieces. I tried to upload a PDF with the vector art, **but the wiki wouldn'​t let me upload a pdf (??).**
 +
 +The fly image used in the actual project isn't really this low-rez, but this is what it looks like post-conversion,​ (especially to the engraver!). You can see in the body where the original grayscale tone translated to a stochastic pattern that is still just black or white pixels only.
 +
 +{{:​woodenbook_2014_c_cut_f_3.png?​320x788}}{{:​woodenbook_2014_c_cut_b.png?​320x843}}{{:​woodenbook_2014_c.png?​320x526}}{{:​wbfly.png?​597x508}}