QUELAB

A place to make things!

User Tools

Site Tools


3dprinters

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
3dprinters [2017/02/23 20:32]
John Benedetto ↷ Links adapted because of a move operation
3dprinters [2019/02/14 05:02] (current)
John Benedetto [Makes and models]
Line 7: Line 7:
 ===== Makes and models ===== ===== Makes and models =====
  
-  * [[prusa_mendel|Prusa Mendel]] +  * [[:prusa_mendel|Prusa Mendel]] 
-  * [[prusai3|Prusa ​i3]] +  * [[:prusai3|Prusa ]] 
-  * [[orion|SeeMeCNC ORION Delta Printer]]+  * [[:blinky|]] - troybot 
 +  * [[:orion|SeeMeCNC ORION Delta Printer]]
   * [[:​makerbot|Makerbot Cupcake / Thing-o-Matic - Thing1 & Thing2]]   * [[:​makerbot|Makerbot Cupcake / Thing-o-Matic - Thing1 & Thing2]]
- 
  
 ===== Training & Problems ===== ===== Training & Problems =====
  
-<WRAP important round> +<WRAP important round> Training is currently in flux. To be trained on the 3D printers, please contact the 3D printing officer via the [[http://​pepper.quelab.net/​mailman/​listinfo/​3d-printing|3d-printing mailing list]] to set up meeting on an open night. Without prior arrangement,​ there is no guarantee that there will be a 3D printing trainer available during an open night, however. </​WRAP>​
-Training is currently in flux. To be trained on the 3D printers, please contact the 3D printing officer via the [[http://​pepper.quelab.net/​mailman/​listinfo/​3d-printing|3d-printing mailing list]] to set up meeting on an open night. Without prior arrangement,​ there is no guarantee that there will be a 3D printing trainer available during an open night, however. +
-</​WRAP>​+
  
 For information on usage, tips and 3D printing stuff, see: For information on usage, tips and 3D printing stuff, see:
  
-  * Using [[3dprinter_usage|MatterControl]] to print models, as well as +  * Using [[:3dprinter_usage|MatterControl]] to print models, as well as 
-  * A set of [[hardware:​3dprinter:​care_and_feeding|troubleshooting and maintenance]] steps.+  * A set of [[:hardware:​3dprinter:​care_and_feeding|troubleshooting and maintenance]] steps.
  
 ===== Materials ===== ===== Materials =====
  
-Different 3D printers accept different materials. Check the page for [[3dprinters#​makes_and_models|whichever printer you are using]] to identify allowable filament.+Different 3D printers accept different materials. Check the page for [[:3dprinters#​makes_and_models|whichever printer you are using]] to identify allowable filament.
  
 The table below specifies costs of materials kept at Quelab. The table below specifies costs of materials kept at Quelab.
  
-<WRAP info> All values are in //​per-gram// ​   increments of ALL consumed materials, **including** ​  ​failed prints and support material.</​WRAP>​+<WRAP info> All values are in //​per-gram// ​ increments of ALL consumed materials, **including** ​ failed prints and support material.</​WRAP>​
  
-^Material ^Members ^Non-Members | +^Material^Members^Non-Members| 
-|ABS |$0.10 |$0.20 | +|ABS|$0.10|$0.20| 
-|PLA |$0.10 |$0.20 | +|PLA|$0.10|$0.20| 
-|NinjaFlex(([[prusai3|Prusa i3]] only)) ​ |TBD: Likely in the $0.60/g range || +|NinjaFlex(([[:prusai3|Prusa i3]] only)) ​   |TBD: Likely in the $0.60/g range|| 
-|IGUS [[http://​www.igus.com/​wpck/​15422/​iglidur_TriboFilament|Tribo]] |Go get a sample from IGUS. It's expensive. ||+|IGUS [[http://​www.igus.com/​wpck/​15422/​iglidur_TriboFilament|Tribo]]|Go get a sample from IGUS. It's expensive.||
  
 Materials must be cleared by a 3D printing officer. Materials must be cleared by a 3D printing officer.
Line 42: Line 40:
 Materials previously cleared for use in the 3D printers: Materials previously cleared for use in the 3D printers:
  
-    ​* Filamentium / FilamentOne PLA Extrafill +  ​* Filamentium / FilamentOne PLA Extrafill 
-    * Zen Toolworks ABS and PLA +  * Zen Toolworks ABS and PLA 
-    * NinjaFlex +  * NinjaFlex 
-    * IGUS Tribo filament+  * IGUS Tribo filament 
 +  * Push Plastic ABS and PLA 
 +  * Taulman Nylon 230
  
 Any material that is in the 3D printing room is considered cleared if it is on the rack above the 3D printers. Any material that is in the 3D printing room is considered cleared if it is on the rack above the 3D printers.
  
 \\ \\
 +
  
3dprinters.1487881954.txt.gz · Last modified: 2017/02/23 20:32 by John Benedetto